Product Overview
Vane type separator adopts corrugated plate technology to dry the gas with low content liquid less than 15%. It applies to the gas-liquid separation in all kinds of occasions in oil and gas field.
Vane type separator has the following kinds(liquid removal /soluble solid removal)
1)Coaxial separator
2)Vertical separator
3)Compressor’s scrubber for suction section and exhaust section
4)Two phase/ three phase separator
5)Degasser
6)Low temperature separator(LTS)
Vane Series
1)Type 624
Features:
- resistance to fouling
- economical
Applications:
- Separating section in the middle of compressor
- purification of the air inlet
- evaporation process
2)Type 624
Features:
- big processing capacity
- small pressure drop
Applications:
- natural gas purification
- waste gas purification
- recycling (such as methyl alcohol, ammonia)
Coaxial separator Vertical separator
Technical Features:
1)High separation efficiency:100% removal of liquid droplets greater than 8μm, 99% removal of liquid droplets 6-8μm.
2)Pressure drop is less than 1.45 PSI.
3)Big handling capacity: Under same working condition and same flow area, the capacity is 4~5 times of mesh mist eliminator.
4)No-blocking, long service life(15~20 years)
Application:
Trial separator in Bei’a
Product Overview:
HHC can be applied to all kinds of oily sewage treatment in oil gas field and refinery. It uses the density difference of
liquid to separate oil droplets from the water by centrifugal separation produced by fluid diversion structure. Oil-water
separation effect mainly depends on the particle size of oil droplet and oil/water density difference, the larger the particle
size and density difference are, the higher the oil water separation efficiency.
Technical Features:
Compared with the traditional products, our de-oiling type HHC has its characteristics, unique hydraulic power calculating
design, high precision casting and processing, especially the CSS, a core component being set in swirl chamber used for
stabilizing and leading flow.
1) Small resistance loss, good condition adaptability: the erosion is reduced by the optimization of the entrance structure
and the improvement of the internal flow passage material;
2) High separation efficiency is guaranteed by precision fabrication and proper installation;
3) Unique oil collecting mouth design can avoid the backmixing of oil and water;
4) Small size, compact structure, convenient installation and easy maintenance.
Technical Index:
Under normal conditions:
Inlet and outlet differential pressure 300~500KPa
Oil removal rate is above 95% when inlet oil conc. is 1000~10000ppm;
Oil removal rate is above 90% when inlet oil conc. is 500~1000ppm;
Oil removal rate is above 80% when inlet oil conc. is 100~500ppm
Oil removal rate is based on the quality of oily sewage and oil particle diameter.
Application Example:
Saudi Aramco IWS System Project
The equipment includes two hydrocyclones, water treatment is 66m3/h.
First stage: inlet oil conc. is 5000ppm,outlet oil conc. is 93-107ppm, second stage: outlet oil conc. is 22-29ppm.
- Metering Module
- Wellhead Monitoring Skid
- Single Well Metering Ski
- Metering Skid for Crude
- Metering Skid for Wet Ga
- Onshore and Offshore Mov
- Metering Skid
- Separation Module
- Gas-Liquid Cylindrical
- Synergistic Three-Phase
- Slug Flow Control System
- Vane Type Separator
- Filter
- GLCC Desander System
- Water Treatment Module
- Micro-Bubble Flotation T
- Hyper-Hydro Cyclone
- Multiphase Pump
- Mobile Electrocoagulatio
- Sulfur Recovery Technolo
- Technology Introduction
- Technology Advantage
- Process Introduction
- Chemical Agents
- Application Cases
- Others
- Chemical Injection Skid
- uel Gas Pressure Regulat